imovie

Same as resume .

Sets the current time location of the movie. If the movie is playing, it will play from the newly set location. 0 is always the beginning. The end time varies from one movie to another. (The length message reports the end time location out the left outlet.)

• location [int]
  

When a QuickTIme movie file is dragged from the Max File Browser to a imovie object, the file will be loaded.

The word active , followed by a non-zero number, makes the movie active (the default). Followed by a 0, active makes the movie inactive. An inactive movie will not play or change location.

• flag [int]
  

Has the same effect as dispose with no arguments.

Removes all movies from the imovie object's memory. If the word dispose is followed by the name of a loaded movie, only the named movie will be removed.

• filename [symbol]
  

Reports the duration of the movie (in milliseconds) from the left outlet.

Reports the end time position of the movie (in Time Units) from the left outlet.

Reports the current rate multiplied by 65536 out the right outlet. Thus, normal speed is reported as 65536 , half speed is reported as 32768 , double speed backward is reported as -131072 , etc. If the movie is not playing, the rate is reported as 0 , and if no movie has yet been loaded nothing is sent out.

Reports the current time location of the movie.

The length message's functionality is equivalent to the getduration message.

The word loadintoram , followed by a non-zero number, attempts to load the entire movie into memory, if possible. The default is 0.

• flag (0 or non-zero) [int]
  

The word loop , followed by a number in the range 0-2, controls looping for the current film on. The options are:
0: looping off (default) 1: looping on 2: palindrome mode (forward and then backward)

• flag [int]
  

Sets the ending point of a loop. The default value the time value that represents the end of the movie.

• endpoint [int]
  

The word looppoints , followed by two numbers, sets the beginning and end points of a loop. the default values are 0 (i.e., the start of the film) for the start point and the end of the film for the endpoint.

• start [int]
  
• end [int]
  

See the looppoints entry.

• start [int]
  
• end [int]
  

Sets the beginning point of a loop. The default value is 0 (the start of the movie).

• startpoint [int]
  

The word matrix , followed by nine floating point numbers, reloads the current movie into RAM after performing a transformation matrix operation on the image. This transformation is the same one used for the mapping points from one coordinate space (i.e, the original image) into another coordinate space (a scaled, rotated, or translated version of the original image).

The transform matrix operation consists of nine matrix elements

• transform [list]
  

Double-clicking on the imovie object will make the movie window active.

The word mute , followed by a non-zero number, turns off the movie's sound (if it has any). Followed by a 0, mute turns on the movie's sound (the default).

• flag [int]
  

The word next , followed by a number, moves the time location ahead by that amount. If no number is supplied, next moves the time ahead by 5. (The actual time meaning of these units varies from movie to movie.)

• time-units [int]
  

Stops the movie if it is playing, and switches to the movie that was loaded just prior to the current movie. (The movies are stored in reverse order from the order in which they were loaded.) If there is no prior movie, nextmovie wraps around back to the most recently loaded movie. Note that the title of the movie window is not automatically changed, even though the "current movie" has been changed by nextmovie .

The word palindrome , followed by a non-zero number, sets the movie to play in palindrome mode (forward and then backward). Looping must be turned on. palindrome 0 (the default) disables palindrome mode.

• flag [int]
  

The word passive , followed by a non-zero number, sets the passive mode. In passive mode, starting a movie will not cause the frame to change unless a bang message is received. passive 0 (the default) sets the movie object to respond to normal start messages.

• flag [int]
  

Pause movie playback

The word prev , followed by a number, moves the time location backward by that amount. If no number is supplied, prev moves the time backward by 5.

• time-units [int]
  

The word quality , followed by a number, sets the minimum interval, in milliseconds, between movie redraws. The default is 0 (i.e., no minimum).

• interval [int]
  

The word rate , followed by one or more integers or floats, sets the playing speed of the movie. If rate is followed by one integer, that number is taken to be a whole number playing speed. If rate is followed by two numbers, the first number is taken to be the numerator and the second the denominator of a fractional speed. 1 is the normal playing speed, 0 means the movie is stopped, and a negative rate plays backwards. rate 1 2 would play the movie at half speed. Immediately after you send a non-zero rate message, the movie will begin playing, so you may wish to precede any rate messages with an integer to locate to the desired starting position.

• speed [list]
  

Same as read .

• filename [symbol]
  

The word read , followed by a symbol, looks for a movie file with that name in Max's file search path, and opens it if it exists, displaying the movie's first frame in a movie window. If the filename contains any spaces or special characters, the name should be enclosed in double quotes or each special character should be preceded by a backslash ( \ ). The word read by itself puts up a standard Open Document dialog box and reads in any movie file you select. The read message will open at least 26 different types of files that can be opened. These include movie files such as MPEG, audio files including AIFF and MP3, and graphics files including GIF and JPEG.

• filename [symbol]
  

The readany message opens any type of file to try to interpret it as a movie or other supported media file.

• filename [symbol]
  

The word rect , followed by four numbers, specifies the size of the rectangle in which the movie is displayed within the movie window. The first two numbers specify the position of the rectangle within the movie window, in relative coordinates, and the second two numbers specify the width and height, in pixels, of the rectangle.

• x [int]
  
• y [int]
  
• width [int]
  
• height [int]
  

The word reload will reload the current movie into memory (can be used to refresh; for example, if a movie is playing and the stop message is sent followed by reload , the movie will reload into memory and be set to play from the beginning as a newly loaded movie).

Begins playing the movie from its current location, at the most recently specified rate.

Sets the movie's rate to 1 and begins playing from the beginning. If the word start is followed by the name of a specific loaded movie, that movie becomes the current movie before starting.

• filename [symbol]
  

The word startat , followed by a number, set the current time location of the movie and begins playing from that point.

• location [list]
  

Stops the movie.

The word switch , followed by a symbol, makes the named movie the active one without changing the transport state (See the start message).

• filename [symbol]
  

The word time , followed by a number that specifies a frame number, goes to the time location specified by the number. When no argument is present, the time message's functionality is equivalent to the gettime message.

• frame [int]
  

Reports the timescale of the movie (the number of Time Units per second) from the left outlet.

The word vol , followed by a number in the range 1-255, sets the movie's sound volume. Optionally, the volume can be set by using the word vol , followed by a floating-point value in the range 0. - 1.0.

• volume [number]